1GS2 GYM SYSTEMCLASS HPART # 7250101REV. CRevision: 11/01/02USER’S GUIDEWARNING:Read and follow all directionsfor each step to insure properassembly o
FIGURE 8 8492936 934STEP 8:• Place PRESS ARM (8) into PRIMARY PIVOT (9) and securely tighten using two 3/8 X 3” BOLTS (29), four 3/8” FLATWASHERS
FIGURE 91101234561/2 1/2 1/2 1/2 1/2 1/2STEP 9• SECURELY TIGHTEN ALL FRAME CONNECTION BEFORE PROCEEDING TO NEXT STEP33376048 91/2 X 8-3/4”SECURE
12STEP 10:• Securely tighten the SPRING PIN (50) to the FRAME (1) and hand tighten the STAR KNOB (52)• Securely assemble one SEAT PAD (13) to
FIGURE 11STEP 11:• Assemble the LEG PEDESTAL (11) to the FRAME (1) using one 1/2 X 104mm BOLT (32), two RH WASHERS (56) and one 1/2” LOW HT L
ILLUSTRATION ANOTE: IF YOU PURCHASED A LEG PRESS, PLEASE REFER TO THECABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEGPRESS KIT14• ILLUSTRATION “
1501234561/2 1/2 1/2 1/2 1/2 1/2• Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.STEP 13: FIGURE 13• As
1601234561/2 1/2 1/2 1/2 1/2 1/2 FIGURE 14• Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.STEP 14:• As
17STEP 15• Screw end of LAT CABLE (20) into top of PLATE SHAFT (18) and securely tighten JAM NUT as shown in FIGURE 1501234561/2 1/2 1/2 1/2 1/2 1/
18• Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.STEP 16:• [CABLE MUST BE POSITIONED BETWEEN PULLEY A
• Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.STEP 17:• Secure end of LOW CABLE (21) using one 3/8
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OFEQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!1. Before using, read all the warnings and
2001234561/2 1/2 1/2 1/2 1/2 1/2• Attach two 4 X 7” ROLLER PADS (15) to the LEG PEDESTAL (11) using one 3/4 X 17” TUBE (14) and two 3/4” STARLO
FIGURE 192617582157ADJUSTMENTADJUSTMENTPULL ANDTWIST TODISENGAGE• If upon completion of assembly, the HEAD PLATE (19) does not sit on top of the f
MAINTENANCEMODEL #________________________SERIAL #_________________________DATE OF PURCHASE: _____________DEALERS NAME: _________________DEALERS PHONE
23NOTES:LIMITED WARRANTYParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN
INTERNATIONAL OFFICESLife Fitness Atlantic BVAtlantic HeadquartersBijdorpplein 25-312992 LB BarendrechtThe NetherlandsPhone: (180) 646 666Fax: (180)
IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the ParaBody GS2 Gym System. Please read these instructions thoroug
Minimum Required Usable SpaceLength = 82 inches (208.5 cm) 6’ 10”Width = 71 inches (180.5 cm) 5’11”Height = 83 inches (211 cm) 6’ 11”1 Square
5PARTS LIST01234561/2 1/2 1/2 1/2 1/2 1/2PART #ACU04-1163ACU04-1158ACU02-1060ACU04-1160ACU04-1384ACU04-1383ACU04-1161ACU04-1164ACU04-1159ACU04-1162ACU
FIGURE 16STEP 1: 13430 2623/8 X 32934 3• LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOLTS (30)
7 FIGURE 3 FIGURE 2• CHECK THAT THE HEADPLATE AND WEIGHT PLATES ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3
• Insert two GUIDE RODS (16) into the BASE (2) asshown on FIGURE 4. (NOTE: If the GS2 SHROUDOPTION was purchased, place the GUIDE RODS(16) through
9STEP 7:• Using hammer tap one 5/16 X 2” ROLL PIN (47) thru LEFT PRESS HANDLE (7) until it is flush with other side of HANDLE as shown in
Komentáře k této Příručce